Welcome to our website

contact us:

Professional Bearing Brand

TIMKEN 29685/29620

TIMKEN 29685/29620

0.00
0.00
  

TIMKEN 29685/29620

PARAMETERS

Timken Part Number 29685 - 29620-B, Tapered Roller Bearings - TSF (Tapered Single with Flange) Imperial

 

 

Specifications

Series

29600

Cone Part Number

29685

Cup Part Number

29620-B

Design Units

Imperial

Bearing Weight

1.5 lb0.70 Kg

Cage Type

Stamped Steel

Dimensions

d - Bore

2.8750 in73.025 mm

D - Cup Outer Diameter

4.4375 in112.713 mm

D1 - Flange Outer Diameter

4.5900 in116.586 mm

B - Cone Width

1.0000 in25.400 mm

C - Cup Width

0.7500 in19.050 mm

C1 - Cup Flange Width

0.1563 in3.970 mm

T1 - Bearing Width

1.0000 in25.400 mm

T - Bearing Width to Flange

0.4063 in10.320 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 0.14 in3.600 mm
r - Cup Backface "To Clear" Radius2 0.130 in3.30 mm

da - Cone Frontface Backing Diameter

3.15 in80 mm

db - Cone Backface Backing Diameter

3.39 in86.10 mm

Da - Cup Frontface Backing Diameter

4.35 in110.49 mm

Ab - Cage-Cone Frontface Clearance

0.08 in2 mm

Aa - Cage-Cone Backface Clearance

0.08 in2 mm
a - Effective Center Location3 0.04 in1 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 6440 lbf28600 N
C1 - Dynamic Radial Rating (1 million revolutions)5 24800 lbf111000 N

C0 - Static Radial Rating

37200 lbf166000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 5370 lbf23900 N

Factors

K - Factor7 1.2
e - ISO Factor8 0.49
Y - ISO Factor9 1.23
G1 - Heat Generation Factor (Roller-Raceway)10 77.7

G2 - Heat Generation Factor (Rib-Roller End)

43.3
Cg - Geometry Factor11 0.117

Tapered roller bearings are rolling element bearings that can support axial forces (i.e., they are good thrust bearings) as well as radial forces.

The inner and outer ring raceways are segments of cones and the rollers are tapered so that the conical surfaces of the raceways, and the roller axes, if projected, would all meet at a common point on the main axis of the bearing. This geometry makes the motion of the cones remain coaxial, with no sliding motion between the raceways and the OD of the rollers.

This conical geometry creates a linear contact patch which permits greater loads to be carried than with spherical (ball) bearings, which have point contact. The geometry means that the tangential speeds of the surfaces of each of the rollers are the same as their raceways along the whole length of the contact patch and no differential scrubbing occurs.

E has different special properties with other inner rings or outer rings marked with the same basic parts code, not interchangeable inner rings or outer rings.

There is a stop ring on the outer diameter of RB



 

PRODUCT ANALYSIS



Model Dimensions(mm) Weight(kg)
d D T
32207 35 72 24.25 0.456
32208 40 80 24.75 0.549
32209 45 85 24.75 0.602
32210 50 90 24.75 0.644
32211 55 100 26.75 0.86
32212 60 110 29.75 1.18
32213 65 120 32.75 1.55
32214 70 125 33.25 1.66
32215 75 130 33.25 1.72
32216 80 140 35.25 2.13
32217 85 150 38.5 2.64
32218 90 160 42.5 3.41
32219 95 170 45.5 4.22
32220 100 180 49 5.05
32221 105 190 53 6.26
32222 110 200 56 7.35
32304 20 52 22.25 0.241
32305 25 62 25.25 0.376
32306 30 72 28.75 0.57
32307 35 80 32.75 0.765
32308 40 90 35.25 1.05
32309 45 100 38.25 1.42
32310 50 110 42.25 1.88
32311 55 120 45.5 2.39
32312 60 130 48.5 2.96
32313 65 140 51 3.6
32005X 25 47 15 0.116
32006X 30 55 17 0.172
32007X 35 62 18 0.23
32008X 40 68 19 0.28
32009X 45 75 20 0.354
32010X 50 80 20 0.38
32011X 55 90 23 0.567
32012X 60 95 23 0.608
32013X 65 100 23 0.646
32014X 70 110 25 0.869
32015X 75 115 25 0.925
32016X 80 125 29 1.32
32017X 85 130 29 1.38
32018X 90 140 32 1.78


PRODUCT SHOWING



 

PRODUCT MODELS

 

Model Dimensions(mm) Weight(kg)
d D T
30202 15 35 11.75 0.053
30203 17 40 13.25 0.079
30204 20 47 15.25 0.127
30205 25 52 16.25 0.157
30206 30 62 17.25 0.238
30207 35 72 18.25 0.34
30208 40 80 19.75 0.438
30209 45 85 20.75 0.488
30210 50 90 21.75 0.558
30211 55 100 22.75 0.736
30212 60 110 23.75 0.93
30213 65 120 24.75 1.18
30214 70 125 26.25 1.3
30215 75 130 27.25 1.43
30216 80 140 28.25 1.69
30217 85 150 30.5 2.12
30218 90 160 32.5 2.6
30219 95 170 34.5 3.13
30220 100 180 37 3.78
30221 105 190 39 4.52
30222 110 200 41 5.28
30224 120 215 43.5 6.28
30226 130 230 43.75 6.83
30302 15 42 14.25 0.098
30303 17 47 15.25 0.134
30304 20 52 16.25 0.172
30305 25 62 18.25 0.27
30306 30 72 20.75 0.403
30307 35 80 22.75 0.538
30308 40 90 25.25 0.758
30309 45 100 27.25 1.01
30310 50 110 29.25 1.28
30311 55 120 31.5 1.63
30312 60 130 33.5 2.03
30313 65 140 36 2.51
30314 70 150 38 3.03
30315 75 160 40 3.63
30316 80 170 42.5 4.27
30317 85 180 44.5 5.08
30318 90 190 46.5 5.67